+86 15868609134info@riverlakeco.com
Products Category
Hydraulic Press

Transformer Relocation In South Africa

Hydraulic Jacking And Skidding System For Transformer Relocation

Project Images

Project Introduction

Taizhou Chuanhu Hydraulic Machinery Co., Ltd delivered 6 double-acting hydraulic cylinders and a petrol-driven hydraulic power unit for the skidding and sliding systems. The Power Pack and hydraulic cylinders are used for electric transformer relocation.

Related Posts

Low Height Pancake Hydraulic Cylinder Used In Auger Boring Steerable Rock System

Low Height Pancake Hydraulic Cylinder Used In Auger Boring Steerable Rock System

Project Images Project Introduction 50-ton low height pancake hydraulic cylinders used in auger boring steerable rock system.Steerable head designed for boring through sand or soft rock with real-time steering adjustments made out of the pit with a hydraulic control system. The Steerable Rock System (SRS) is the auger boring market’s first steerable head designed to navigate not only solid rock but difficult fractured rock conditions as well. Engineered to operate in rock up to 25,000 psi, the SRS allows operators to keep bores online and grade even in the toughest ground conditions for an on-grade bore. On the drilling head, there is peace’s of small round pipe, that’s where the cylinders sit. There are 4 pcs 50-ton pancake hydraulic cylinders on each side(top, bottom, right, and left) of the steerable head for a total of 16pcs, it works when it’s drilling horizontally underground we use the cylinders to navigate the drilling head.
DIY: How to Replace Damaged Hydraulic Cylinder Seals

DIY: How to Replace Damaged Hydraulic Cylinder Seals

Hydraulic cylinder seals are commonly damaged in a variety of ways. The most common cause is a mechanical failure, such as over-torquing or sudden load changes. Other causes include contamination and wear caused by oil and grease, water, and other fluids. Damage to the seal can lead to leakage, which can be extremely costly to repair. Step 1: Order a new set of seals for your hydraulic cylinder To repair the cylinder, you will need a new set of seals. You can either buy new seals directly from your cylinder manufacturer or you can get the required seal part number and buy them from a local hardware store. Step 2: Preparation work before you disassemble the cylinder Before disassembling the hydraulic cylinder, it’s important to clean it and remove all dirt, grease, oil, and other contaminants. You do not want these contaminants to get inside the cylinder or the hydraulic system. You need to do the disassembly work in a clean workspace. If you are in the field, you can put down a clean tarpaulin and do the repair on this. Step 3: Disassemble the hydraulic cylinder step by step It can be hard to know where to start when disassembling a hydraulic cylinder. First,
Hydraulic Testing Projects With China National Offshore Oil Corporation

Hydraulic Testing Projects With China National Offshore Oil Corporation

Project Images Project Introduction Hydraulic Testing Projects With China National Offshore Oil Corporation
Electric Hydraulic Pump

How Does a Hydraulic Pump Work?

A hydraulic pump is a machine that uses the power of fluid to move objects. The first pumps were invented in the seventeenth century, and they were mainly used for irrigation. Over time, however, hydraulic pumps have been used for a variety of other purposes, including mining, manufacturing, and moving objects. How Does a Hydraulic Pump Work? A hydraulic pump is a machine that uses the pressure of fluids to move things. It works by using a piston and cylinder assembly to push and pull fluid through a series of tubes. The force of the fluid moving through the tubes creates a mechanical force that can be used to do work. There are two main types of hydraulic pumps: reciprocating and impeller. A reciprocating pump has a piston that moves back and forth inside the cylinder. The force created by this motion is used to push or pull fluid through the system. An impeller is a spinning cylinder, and it can be used as a reciprocating pump or as an aerator. The main components of a hydraulic pump are pistons, cylinders, valves, and pipes. They are all connected together in order to create a system that can move fluids. A piston is